Stage 1 Performance Kit for Ski-Doo 850 E-TEC (Long Track / Mountain) // SKU: 13-213
KIT CONFIGURATION & OPTION SELECTION:
- Step 1 (Select Fueling / Tuning Option): Choose your preferred calibration setup above—Torque Link Pro (recommended for wireless mobile flashing & full diagnostics), ECU Hard Flash, or 5% Plug-and-Play Fuel Module.
- Step 2 (Select Elevation & Manifold Finish): Choose High Elevation (6,000+ ft) or Low Elevation (0–6,000 ft) to automatically configure both your Stage 2 Clutch Kit and matched Exhaust Pipe Stinger, then select your Performance Manifold (Y-Pipe) finish (Ceramic Black or Ceramic Chrome).
- Included Bundle Components: All matching exhaust and clutching components are pre-selected as a complete, calibrated package. If you already own certain components and only need individual parts, click any item link in the breakdown below to order separately.
Kit SKU: 13-213
Horsepower Gain: +10–12 Peak HP (Dyno-Proven System Gain)
Target Operating RPM: 7,900–8,000 RPM
Primary Application: 2017+ Ski-Doo REV Gen4 & Gen5 850 E-TEC Naturally Aspirated (NA) mountain snowmobiles equipped with 2.0" to 3.0" lug tracks (Summit & Freeride).
Unlock the full potential of your Ski-Doo 850 E-TEC in one complete, dyno-matched bolt-on package with the Bikeman Performance Stage 1 Long Track Performance Kit. Rather than piecing together mismatched aftermarket parts, this complete system synchronizes precision fuel/ignition calibration, high-velocity exhaust scavenging, and our proven Stage 2 mountain clutch setup to deliver a reliable 10 to 12 horsepower gain, substantial front-end weight savings, and razor-sharp throttle response in deep snow.
By dialing in your ECU calibration, opening up exhaust flow with our Fatt Azz Expansion Pipe and High-Flow Performance Manifold (Y-Pipe), and transferring every extra pony directly to the snow with our adjustable pDrive and QRS clutching, your 850 E-TEC pulls harder on steep climbs, recovers instantly in tight tree lines, and holds dead-steady at its 7,900–8,000 RPM peak powerband.
Complete Kit Breakdown
1. Fueling & ECU Tuning (Step 1 — Select Your Setup Above)
Adding a full pipe and Y-pipe increases airflow and requires proper fuel and timing calibration. Select the tuning solution that best fits your riding style and diagnostic needs:
- Torque Link Pro Tuning System [Device + License + Ski-Doo Cables] (Recommended): Our flagship wireless mobile tuning and diagnostic platform—flash and monitor your sled directly from your iOS or Android phone with no PC or ECU mail-in required. Includes full access to Bikeman's dyno-developed Stage 1 fuel and timing calibrations, live data logging, launch control, component relearns (power valves, oil pump, keys), and fault code diagnostics.
- ECU Hard Flash (Mail-In Bench Calibration): Send in your factory ECU to be bench-flashed with Bikeman's dyno-developed Stage 1 calibration. Optimizes both fuel mapping and ignition timing curves, removes restrictive factory limits, and delivers maximum throttle crispness and peak horsepower.
- 5% Plug-and-Play Fuel Module [SKU: 24-201]: Simple, inline plug-and-play module that adds a consistent +5% fuel enrichment across the entire RPM and throttle range to safely match your new exhaust flow. Requires no ECU rewriting or flashing and maintains your factory warranty. (Note: Provides straight fuel addition without ignition timing adjustments or factory emissions parameter changes.)
2. Exhaust System (Pipe, Elevation Stinger & Choice of Y-Pipe Finish)
- Fatt Azz Expansion Pipe [SKU: 01-214-C]: Dyno-engineered high-volume expansion chamber designed specifically for the naturally aspirated 850 E-TEC engine. Sheds significant weight over the bulky OEM pipe while optimizing exhaust gas scavenging to boost mid-range torque and top-end horsepower.
- Elevation-Calibrated Pipe Stinger (Included): Automatically matched to your selected riding altitude in Step 2 (High Elevation 6,000+ ft or Low Elevation 0–6,000 ft) to maintain proper expansion chamber backpressure and peak RPM consistency.
- Bikeman Performance Manifold / Y-Pipe: Smooth-transition, high-flow manifold that eliminates restrictive factory casting pinch points for stronger exhaust scavenging. Available in your choice of Ceramic Black [SKU: 03-213] (maximum heat retention and stealth look) or Ceramic Chrome [SKU: 03-213-C] (classic high-luster thermal finish).
3. Stage 2 Long Track Mountain Clutch Kit [Base SKU: 06-25-LT]
Pre-calibrated to put your added 10–12 HP directly to the track without belt slip or high-RPM fade. Automatically configured based on your elevation selection in Step 2:
High Elevation Clutch Setup (6,000+ ft) [SKU: 06-25-201]:
- Goldstar Adjustable Clutch Weights (44–58g) [SKU: 05-GSW-4458]: Mountain-profile primary weights with tool-free magnetic snap-in tuning and 5-step corrosion-resistant finish.
- pDrive Adjustable Weight Pivot Bolt Kit [SKU: 05-202]: Upgraded 5mm hex bolts and 1.2g tuning shims allowing quick pivot mass tuning down to 12.0g without pulling ramps.
- Primary Drive Clutch Spring (173-385) [SKU: 05-173-385]: Shot-peened alloy spring for crisp engagement and controlled upshift under continuous mountain load.
- QRS XP4 Progressive Secondary Clutch Helix [SKU: 05-XP4]: Multi-angle ramp geometry engineered to maximize belt clamp, lower sheave temps, and snap backshift response.
- Ski-Doo 19T Top Chaincase Gear [SKU: TP-351519-002]: 1-tooth gear reduction (13-wide / 15-spline hardened steel) by TEAM Industries to multiply track torque at altitude.
- Smooth Shift Secondary PTFE Teflon Washers (3-Pack) [SKU: 05-TW-201-3]: Low-friction thrust washers that eliminate secondary spring bind and stabilize shift curves.
- Note: High-elevation clutch configuration retains your factory OEM secondary spring.
Low Elevation Clutch Setup (0–6,000 ft) [SKU: 06-25-202]:
- Goldstar Adjustable Clutch Weights (48–62g) [SKU: 05-GSW-4862]: Heavier base-mass magnetic adjustable weights calibrated to load the 850 engine under full sea-level barometric pressure.
- pDrive Adjustable Weight Pivot Bolt Kit [SKU: 05-202]: Upgraded 5mm hex bolts and 1.2g shims for fast pivot weight adjustments without removing ramps.
- Primary Drive Clutch Spring (173-385) [SKU: 05-173-385]: Consistent 173 lb initial bite and 385 lb finish load control.
- QRS Secondary Clutch Spring (205-310) [SKU: 05-QRSS-205310]: High-rate secondary spring providing firm belt side-pressure under full low-elevation power.
- QRS XP2 Progressive Secondary Clutch Helix [SKU: 05-XP2]: Low-elevation progressive angle cut for hard acceleration and clean mid-range upshift.
- Smooth Shift Secondary PTFE Teflon Washers (3-Pack) [SKU: 05-TW-201-3]: Eliminates secondary spring bind and maintains smooth, repeatable shift action.
- Note: Low-elevation clutch configuration retains your factory OEM chaincase gearing.
Key Performance Benefits
- +10 to 12 Dyno-Proven Horsepower: Every component—tuning, exhaust, and clutching—is engineered together on our SuperFlow dyno for measurable gains you feel immediately on the snow.
- Significant Weight Reduction: Replaces heavy, restrictive OEM exhaust components with our lightweight performance pipe and Y-pipe for quicker sidehilling and nimble handling.
- Zero Belt Slip & Cooler Clutch Temps: Stage 2 clutching puts the extra horsepower straight to the track while dropping belt operating temperatures and sharpening backshift recovery.
- Flexible Tuning Path: Take full wireless control of flashing and diagnostics with Torque Link Pro, opt for a bench ECU Hard Flash, or choose warranty-friendly plug-and-play fueling with the 5% Fuel Module.
Vehicle Fitment & Compatibility
-
Compatible Sled Models: Fits all 2017+ Ski-Doo REV Gen4 and Gen5 850 E-TEC Naturally Aspirated (NA) mountain snowmobiles running 2.0" or deeper lug tracks:
- Ski-Doo Summit 850 E-TEC (146, 154, 165, 175 — Expert, Edge, X, SP)
- Ski-Doo Freeride 850 E-TEC (146, 154, 165 with 2.5"+ lug tracks)
- Naturally Aspirated (NA) Models Only: Engineered exclusively for naturally aspirated 850 E-TEC models. Factory 850 Turbo and Turbo R models require turbo-specific performance packages.
- Short Track / Trail Models: For MXZ, Renegade, or Backcountry models running track lugs under 2.0", select our Ski-Doo 850 Short Track / Trail Performance Kit.
- Recommended Installation Accessories: For a 100% leak-free manifold seal during installation, pair your kit with a fresh Cometic 850 E-TEC Exhaust Y-Pipe Gasket Pair [SKU: cm-ex170904am x2].
